Manufactured Homes Without Steel Chassis: Will the New Law Transform the Industry?

For nearly 50 years, one feature has distinguished HUD-code manufactured homes from many other forms of residential construction: the permanent steel chassis beneath the home. A new federal law changes that requirement—and may eventually change much more than the construction process.

On July 11, 2026, the 21st Century ROAD to Housing Act became law. Section 301 changed the federal definition of a manufactured home from one built “on a permanent chassis” to one built “with or without a permanent chassis.”

Will this make manufactured homes cheaper? Will HUD-code and modular homes increasingly resemble one another? Could manufacturers create different home designs—and eventually enter neighborhoods where manufactured housing has historically been restricted? The answers matter to North Carolina builders, investors, lenders, and local governments.

What Did the New Law Actually Change?

Manufactured homes are built under the national construction and safety standards administered by the U.S. Department of Housing and Urban Development (HUD). Traditionally, a permanent steel chassis was a defining characteristic of a HUD-code home. Modular homes, by contrast, are generally built under the state and local building codes that also govern site-built homes.

The new legislation permits HUD-code homes with or without permanent chassis. It also directs HUD to establish revised standards, including distinguishing labels for chassis-free homes, and requires states to provide consistent regulatory treatment to manufactured homes with and without a permanent chassis in areas such as title, financing, insurance, transportation, and installation.

This is an authorization for a new construction pathway—not an announcement that every chassis-free design can be produced and installed immediately. HUD still must address technical requirements. Its October 2026 Next Generation Manufactured Housing Action Plan identifies design, transportation, lifting, foundations, anchoring, and installation among the subjects needing further development.

North Carolina has already responded legislatively. Session Law 2026-59 (Senate Bill 445), effective October 1, 2026, updates the state's definition of manufactured housing to conform with the federal definition.

Will Removing the Steel Chassis Actually Save Money?

Reducing steel content sounds like a straightforward cost saving. A permanent chassis requires material and fabrication labor, and eliminating it could reduce the factory cost of some homes. But the useful comparison is not simply the factory's steel bill. It is the total delivered and installed cost of a finished home.

The chassis of a traditional manufactured home has several functions. It supports the structure during transport and helps installers move, position, level, and support the home at its destination. A typical double-wide can be delivered in sections and placed on an engineered pier-and-footing foundation system.

A chassis-free design will need a different structural and installation approach. Depending on how a manufacturer engineers it, transportation might use a removable carrier; setting might require specialized lifting equipment or a crane; and some designs may use more substantial permanent foundations. Those costs could offset some or all of the manufacturing savings.

It is important not to assume every chassis-free home will require a crane or a continuous concrete foundation. Manufacturers may devise efficient alternative systems, including engineered pier arrangements. The installation practices and costs will vary by product, and HUD's standards are still being developed.

For a conventional 1,200–1,600-square-foot double-wide on a rural North Carolina lot, today's manufacturing and installation system may already be very cost-effective. Chassis-free construction will need to demonstrate a measurable benefit rather than simply promise cheaper housing because it uses less steel.

The question isn't how much steel costs can be eliminated. It's whether the entire delivered, installed, and permitted home costs less.

Manufactured Versus Modular: Three Possible Paths

The chassis requirement has long been one of the clearest physical differences between HUD-code manufactured homes and modular homes. Removing it could make the products much more similar in design, appearance, and installation. But their building-code pathways would remain distinct unless regulations change further.

Path 1: Two Distinct Products Continue

Traditional manufactured homes remain focused on lower-cost construction and rural land-home packages, while modular homes retain advantages where a home must comply with the state residential building code. Chassis-free models add flexibility without fundamentally changing those market segments.

Path 2: HUD-Code Homes Compete More Directly With Modular Homes

Manufacturers begin offering conventional-looking homes with permanent foundations, more varied dimensions, and potentially multiple stories. Some buyers and developers may choose these homes instead of modular construction if a national HUD construction standard delivers the combination of design, market access, and price they need.

Path 3: A Broader Factory-Built Housing Industry Emerges

Manufactured and modular factories could increasingly use similar designs and production processes, even if some homes continue to be certified under the HUD Code and others under state building codes. Buyers might focus more on floor plan, quality, price, financing, and location than on the manufactured-versus-modular label.

This third scenario is speculative, but HUD's 2026 action plan does contemplate a pathway for modular and other off-site manufacturers to enter the federal manufactured-housing regulatory system. Modular housing would not necessarily disappear: complying with a state residential building code may remain valuable in markets where HUD-code housing faces land-use or financing constraints.

New Designs May Be the Bigger Opportunity

Permanent chassis have shaped the dimensions, transportation methods, and engineering of manufactured housing for decades. Greater flexibility could help manufacturers pursue new architectural forms, including narrower homes on small lots, two-story configurations, traditional-looking ranch homes, and more elaborate multi-module designs.

Other possibilities include townhouse-style layouts and certain small multifamily concepts—but these would still depend on future construction standards, engineering, zoning, and product-specific approvals. The new law does not by itself authorize every conceivable design.

For example, a two-story factory-built starter home might fit a smaller infill lot better than a wide, single-story double-wide. A chassis-free ranch home on a conventional foundation might also fit more naturally into an established subdivision. In those cases, the value of the design freedom could exceed any direct savings on steel.

Could Chassis-Free Homes Change Municipal Zoning?

This may be the most important long-term question for North Carolina investors. Some local residential districts allow modular and site-built houses but restrict HUD-code manufactured homes. A new chassis-free HUD-code model might look virtually identical to a neighboring modular home and yet still face manufactured-housing zoning restrictions.

North Carolina's G.S. 160D-910 limits outright exclusion of manufactured homes from an entire local zoning jurisdiction while permitting local land-use and appearance regulations within statutory limits. The new federal chassis law does not automatically require municipalities to allow HUD-code homes wherever modular or site-built homes are permitted.

Nevertheless, municipalities may face increasingly difficult policy questions. If a HUD-code home has a conventional roofline, attractive exterior, permanent foundation, and appearance comparable to a modular home, what specific planning objective justifies treating the two differently? Neighborhood concerns about appearance could become less persuasive if the products are visually indistinguishable.

That does not guarantee zoning reform. Local decisions may be influenced by building-code distinctions, development patterns, political resistance, and financing realities. But a wider range of attractive designs could make more jurisdictions willing to reconsider old restrictions—particularly where starter-home supply is limited.

What Could This Mean for North Carolina Real Estate Investors?

Consider two business models. The first is the familiar rural land-home package: acquire a suitable lot, install a double-wide, complete the septic, utilities, access, and other improvements, and sell the property. For this project, a conventional chassis may continue to be the most economical choice. The new design flexibility might provide little added value.

The second model is a smaller suburban infill lot where demand for entry-level homes is strong but conventional manufactured housing is currently difficult to permit. A chassis-free HUD-code house might eventually offer an attractive alternative to a modular or small site-built home—assuming the zoning and approvals permit it.

That second home could cost more to deliver and install than a traditional double-wide and still be a better investment. Its value may come from reaching a stronger market with a higher attainable sale price, not from eliminating the steel chassis.

Investors should not underwrite that opportunity prematurely. Before acquiring a lot for a new product, they will need confirmation of local zoning, manufactured-home approval, installation costs, comparable completed sales, end-buyer mortgage availability, and the builder's ability to complete the project on time.

Financing, Appraisals, and Real Property

A home without a permanent chassis does not automatically become a modular or site-built home for legal and lending purposes. The federal legislation maintains its status as a HUD-code manufactured home and seeks consistent state treatment between chassis-based and chassis-free models.

For a private construction lender, the critical considerations remain familiar: can the home be properly secured as real property; is the installation compliant; are there defensible comparable sales; and can the eventual buyer obtain suitable mortgage financing? A new category of products may initially present appraisal, title, underwriting, and insurance questions until standards and market practices mature.

For background on those distinctions, see our article Understanding Real Property vs. Personal Property in North Carolina Manufactured Homes and our comparison of Modular vs. Manufactured Homes.

A Small Legal Change With Potentially Large Consequences

Eliminating the permanent chassis requirement is unlikely to have the same impact across the manufactured-housing industry. For today's common double-wide land-home package, savings may prove modest once alternative transportation and installation expenses are included. For new designs on small lots and in more conventional neighborhoods, the change could be transformative.

The next several years will reveal how manufacturers engineer chassis-free homes, whether builders can install them economically, how mortgage markets respond, and whether North Carolina municipalities expand their permitted uses.

The greatest opportunity may not be building the same manufactured home for less money. It may be building a different kind of HUD-code home in places where manufactured housing has never been able to compete.

Mobile Home Money provides business-purpose private lending to North Carolina investors building and flipping manufactured, modular, and small site-built starter homes. We follow regulatory and industry developments that may affect site selection, budgets, financing, and investment returns.

Sources and Further Reading